Battery auxiliary cable
If your car does not turn on after starting, the battery or battery cables may be damaged. To check this issue, you need to check the battery and battery cables to find out which one is bad.
First check the battery. If the battery has lost its charge, it will be charged with a little battery and it will turn on. If the battery is damaged, it will not turn on with the battery. By choosing a quality battery for your car, such as Suzuki car battery, Delcor, etc., get rid of the trouble of frequent battery failure.
If you are sure about the health of the battery and other parts that are related to starting the car, there is a possibility that the battery cables are damaged and you should check the cables. If the cables are damaged, replace the car battery cable.
How is a faulty battery diagnosed?
By turning the switch, the car engine does not start.
None of the car’s electrical equipment is working.
It is difficult to start the car and it starts weakly.
The car shuts off suddenly while driving.
What role does the battery cable play in the car?
The battery cable plays an essential role and if it is defective, it should be replaced. This cable establishes a connection between the car’s electrical system and the car’s battery. If this connection is not made, it will not be possible to start the car.
Failure of the cable can cause a decrease in the electric current entering the starter section or no electric current entering the starter section. Changing the car battery cable does not cost much and is a very easy and inexpensive task. If you have little technical skills, you can easily do it yourself. Of course, you need tools for this.
We remind you again that before changing the cables, make sure of their failure. The reasons for the car not starting may be battery failure, starting system failure, battery sleep, etc. If you cannot determine whether the cables are damaged or not, be sure to go to a repair shop or battery shop. Next, we will examine how to change the cables.
Battery-to-battery cable, as the name suggests, is specific to the car battery. Your car battery is an important part of your car and it provides one of the most important features: starting the car. This device is primarily used to start the car engine, but it also helps to turn on auxiliary components of the car, including lights, radio, etc.
لیست موضوعات مقاله
ToggleWhat is a battery to battery cable?
Battery-to-battery cables, also known as booster cables or jumper cables, are a pair of insulated wires with two clamped ends. These wires have enough capacity to connect the equipment and the vehicle with an auxiliary source, so these two devices that are supposed to be connected must be of the same voltage.
There are many reasons and conditions that can cause your battery to fail or drain, such as cold weather, leaving your car lights on for too long, or even an old or ineffective battery. However, sometimes using a battery-to-battery cable can help and solve all of your battery problems in the short term, or at least get your car to start so you can drive it to a mechanic shop and see what the bigger problem is. . To use a battery-to-battery cable, you need special tools and a little knowledge. But never fear, this article from Electro Sanat Tehran will tell you all the points you need to know about it.
Battery to battery cable specifications
You must use standard cables to prevent sparks or connecting wires. Because this work requires high current, if you use normal and non-standard wires, it will melt the wire and the connection, which is dangerous and damaging.
The length of the battery connection cable
Before buying a battery to battery connection cable, you might think that buying a battery connection cable with a length of more than 1. 5 or 2 meters is extra cost. But for reasons such as frost, the one-way street, etc., you cannot always and everywhere park cars corner to corner.
Therefore, we suggest you to buy a longer battery cable so that you don’t have to worry about the cable not reaching the car.
Battery cable diameter size
The appropriate cable size for battery to battery is one of the things that you must consider. Because at the beginning of the start, a high amp enters the cable.
Therefore, when buying a cable, be sure to check the amp that the manufacturer has inserted for the cable. The larger the diameter or the grade of the battery wire, the higher the amperage it can withstand.
Normally, a 4 or 6 grade copper wire or cable is suitable for normal cars.
Battery cable material
The material of the cable must be pure copper, because copper is more conductive than aluminum or copper-coated aluminum cables.
Another characteristic of a good cable is that the wire or cables are placed in a sheath or attached to each other (except for the end of the wire that reaches the copper wire clip, which must be free) so that the cable does not get twisted and takes up less space. do
Positive and negative battery connection cables
Standard jumper cables are red and black. If you have cables of the same color, mark them with any possible means so that you don’t make a mistake when using them, because one of the cables (red type) must be between the positive terminals and the other cable (black type) between the negative terminal of a healthy battery and The ground point (described below) should be connected.
The material of the battery connector clip
In the market, there are both copper and aluminum scorpion clamps. As we said in the previous section, copper is the best conductor, for this reason, it is better to have the same material of the cable and the clamp of your battery, and of the type of clamp of high ampere to be able to conduct the necessary ampere.
Connecting the cable to the clip of the battery head
When buying a battery-to-battery cable, you should also consider connecting the cable to the battery head clip. The cable is first connected to a piece called cable, then it is screwed to the Susmari clip. Of course, in some models, the cable is directly connected to the tooth.
In any case, in a good cable, after pressing the cable to the car connection cable, soldering is also done to form a stronger connection.
Battery clamp spring
Another point to pay attention to when buying a battery-to-battery cable is the material and durability of the spring of the battery head clip.
The material of the battery connector spring must be made of steel so that the lizard clip does not get rusted. Also, the spring of the susmari clamp must be strong to cause the teeth to collide with the battery.
Susmari connection clamp teeth
When buying a car battery cable, it is better to use a serrated battery head clip to have a stronger connection. In addition, it is better that the cable has the possibility of biting the battery head both from above and from the side.
Insulation of the battery connector
One of the other points that should be paid attention to when buying a battery-to-battery wire is the insulation of the Susmari clamps themselves, in addition to its handle. Because connecting the clamps causes a lot of damage to the car.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Buy the right battery-to-battery wire
The difference between a battery wire and a normal wire: Usually, the size of the wire and cable is determined according to the amperage of the battery system and the required length of the cable to reach from point A to point B. Using the wire and cable size table can help you make the right choice.
Below are some recommendations that you should definitely consider before doing the work.
- Before preparing the battery connection cables, pay attention to the length of the cables and the insulation on them. The length of the cables should be long so that you can easily connect two batteries together. Also, the insulation on the cables must not be damaged because bare wires are dangerous.
- Be sure to use standard cables with high safety because it guarantees your safety. If your battery connection cable is worn, be sure to purchase a new cable.
- Be sure to use safety gloves before connecting the cables.
- Never connect the cables to the terminals before making sure that the positive and negative terminals are identified.
- Never attach the cable clamps to any part of the car engine.
- After completing the charging process, let the car work for a while.
- Try to learn the correct way to charge the car from battery to battery and remember it because your smallest mistake will have dangerous consequences.
Making battery to battery cable
If you don’t intend to buy a battery-to-battery cable online and want to make it yourself, we will teach you the necessary tools and how to make a battery-to-battery cable in a video:
Necessary tips for making cables
In the market, there are different types of electrical cord clamps, and there is no need to make a cord clamp. In terms of size, you can buy a large or medium susmari clip based on your needs, whether you only want a car connection cable or use this cable for other connections (although the price of a large susmari clip is higher), but for the car connection cable, the length of the susmari clip is the same. It is enough to be the size of the battery head.
In addition to the material of the cable, which is copper, try to take the clamps with copper amp clamps to have the best battery-to-battery cable.
Strong battery to battery cable
If the price of the battery-to-battery cable you are making is not important to you, we suggest using welding cable, which is very strong, but if the price of the battery-to-battery connection wire is important to you, the 4-6 grade wire is the answer for you.
Is it more cost-effective to make a battery-to-battery cable or buy a battery-to-battery cable?
If you have the necessary tools to make a battery-to-battery cable and you don’t find the right size for your battery-to-battery cable, you can do it yourself with the help of the tutorial video above. But you should keep in mind that the price of the battery wire to the car battery for a manufacturer will definitely be lower than the cost for you.
Application of battery wire to car battery
Almost everyone who has enough driving experience has certainly experienced the feeling of a dead car battery. A car battery, if used correctly, will have an average life of five to seven years.
Next, you have to find out what exactly is the problem? What caused the battery to stop working? Is the battery just empty or completely burned out? But for now, your only goal is to restart the car as quickly as possible and continue on your way.
If you are physically strong or have people to help you, or if you have stopped somewhere where you can park the car on a slope, you can use the old-fashioned push-and-start method. For this, you need to put your car in gear and hold the clutch pedal, after the car has moved far enough, quickly release the clutch and start the car.
After this, we come to the most popular method of starting a car with an empty battery, using a battery-to-battery cable or jumper wire. It is in such cases that knowing how to use the car battery connection cable will be very useful.
How to use battery to battery cable
Checking the voltage of batteries to do battery by battery
The first thing you need to do for battery charging is to choose a battery charger. Of course, you cannot use any type of battery because the receiver and donor batteries must have the same voltage (of course, the battery voltage of all passenger cars is 12, but be careful).
For this, open the hood of both cars and check the voltage of the batteries indicated on it. Because if the voltages are unequal, a battery with a higher voltage will cause damage after connecting to a battery with a lower voltage.
Steps to turn on the car using a battery to battery cable
To use the battery-to-battery method correctly to start the car, do the following steps in order:
- Place a healthy car (with an active battery) in front of the car that won’t start, so that the battery connection cable can be used without stretching it too much.
- Clean the terminals thoroughly to remove corrosion.
- Turn off the ventilation system, broadcast system, lights and all electrical devices in both cars (if they are on, they may burn and be damaged when connected)
- The battery-to-battery cable has 2 positive (red) and negative (black) wires, each wire has 2 ends, that is, 2 positive ends and 2 negative ends. Make sure you know the positive and negative sides.
- Connect the positive (red) cable to the positive terminal of the dead battery.
- Connect the other end of the positive cable to the positive terminal of the car battery.
- Connect the negative (black) cable to the negative terminal of a healthy and active battery.
- Connect the other end of the negative cable to a part of the dead car that is metal and has no paint.
Note : . pay attention to the order of the connections mentioned above .
- After a healthy battery works for a few minutes, the dead battery is charged and the car can be started
- After the dead battery is activated, disconnect the black negative cable from the colorless metal part and then disconnect the other end of the negative cable from the negative terminal of the healthy car.
- Disconnect the positive cable from the healthy battery, then disconnect the other end of the positive cable from the previously failed battery.
Note : . The steps of disconnecting the cables are just the opposite of the steps of connecting them .
- Let the car whose battery has failed before start working for a while (10 minutes) and help it work by giving it a little gas.
Note : .The order of the above steps is important, otherwise it may cause sparks or even explosion
How to use battery to battery cable correctly
Tips for using the car battery connection cable
Pay attention to some of the battery-to-battery cables, if you look carefully, the red and black wires have different diameters, so you should pay attention to the following points:
- When charging the battery, connect the stronger cable to the positive pole of the battery.
- Connect the negative cable of the car whose battery is dead instead of the battery to the car body (the farthest possible point from the other pole).
- Most of the Iranian cables do not have a solid and strong cable end, so try to make sure the connection is solid before the first start, and even if possible, hold the cable end with your hand firmly during the start.
Battery to battery cable steps
Does your car not start? It may look like your battery is dead, but if the lights and electrical systems still work, your battery may need a battery-to-battery cable. Follow the steps below to get your battery up and back on the road.
Step 1: Finding the Battery to Battery Cables (Jumper Cables)
The first step in the battery-to-battery cable is that you will need a set of jumper cables and another vehicle with a charged battery. You can find jumper cables at auto parts stores, at gas stations, or anywhere you can buy auto accessories.
Step 2: Park two cars side by side
A car that needs a battery-to-battery cable is placed next to a car with a full battery. Place the cars close enough so that the cables can easily reach from one car’s battery to the other. Turn off the engine of both cars and open their hoods depending on where the batteries are located.
Step 3: Find the red (positive) and black (negative) terminals.
Locate the battery terminals. Each battery has two metal terminals. One is a positive sign (+) and the other is a negative sign (-). There are positive and negative cables in the jumper cable. Red is positive (+) and black is negative (-). Never connect the red cable to the negative battery terminal or to a vehicle with a completely dead battery.
Step 4: Determine the metal plate in the car with low battery
Identify a metal plate inside a vehicle that has a low battery. You can use the metal frame of the vehicle.
Step 5: Positive terminal of the car with a low battery
At this stage of the battery-to-battery cable, you must connect the positive end of the jumper cable to the positive (+) terminal of the vehicle that has a low battery.
Step 6: Car positive terminal with full battery
Connect the other positive end of the jumper cable to the positive (+) terminal of the car with a full battery.
Step 7: Negative car terminal with full battery
The negative end of the battery-to-battery cable will transfer current to the negative terminal of the car that is going to the low-charged car battery.
Step 8: Metal plate in car with low battery
Connect the other negative end of the battery-to-battery cable to a metal part of the vehicle with a low battery. You can use the engine body or another metal surface that is far from the battery. This is the last connection you should make.
Step 9: Turn on the low battery car
Start the car with a full battery. Wait a minute or two and try to start the low battery car. If the car starts: proceed as follows:
- Remove the negative end of the black battery-to-battery cable from the metal plate of the car that needs charging.
- And disconnect the other negative end of the black cable that is connected to the auxiliary vehicle.
- Remove the positive end on the red cable from the auxiliary car.
- Disconnect the other positive end that was connected to the low battery car before.
If the car does not start, wait a few moments and repeat step 9 again. We recommend that you fully charge your car as soon as possible after the battery-to-battery cable.
1000 battery auxiliary cable
Product features
- Application: repair shop – battery making
- Model: 1000 amp battery auxiliary cable
- Ability: Use to connect battery to battery of light and heavy vehicles
- Current passing power: 50-60 amps
- Cable material: resistant plastic
- Cable core material: copper
- Clip material: metal
- Clamp handle material: insulating plastic
- Cable length: 200 cm
- Clip length: 20 cm
- Weight: 1,500 kg
- Warranty: one year
- Producer: Electro Sanat Tehran
- Country of manufacture: Iran
Click the button below to view the types of battery auxiliary cable 1000 of Electro Sanat Tehran company, inquire about the updated price and buy battery auxiliary cable 1000.
1500 battery auxiliary cable
Product features
- Application: repair shop – battery making
- Model: 1500 battery auxiliary cable
- Ability: Use to connect battery to battery of light and heavy vehicles
- Current passing power: 1500 amperes
- Cable material: resistant plastic
- Cable core type: copper
- Clip material: metal
- Clamp handle material: insulating plastic
- Cable length: 200 cm
- Clip length: 20 cm
- Weight: 1,500 kg
- Warranty: one year
- Producer: Electro Sanat Tehran
- Country of manufacture: Iran
Click the button below to view the types of 1500 battery auxiliary cable of Electro Sanat Tehran company, inquire about the updated price and buy 1500 battery auxiliary cable.
2000 battery auxiliary cable
Product features
- Application: repair shop – battery making
- Model: 2000 battery auxiliary cable
- Ability: Use to connect battery to battery of light and heavy vehicles
- Current passing power: 2000 amperes
- Cable material: resistant plastic
- Cable core type: copper
- Clip material: metal
- Clamp handle material: insulating plastic
- Cable length: 200 cm
- Clip length: 20 cm
- Weight: 1,500 kg
- Warranty: one year
- Producer: Electro Sanat Tehran
- Country of manufacture: Iran
Click the button below to view the types of battery auxiliary cable 2000 of Electro Sanat Tehran company, inquire about the updated price and buy battery auxiliary cable 2000.
conclusion
We hope this guide has been helpful in showing you what to do (and what not to do) with the battery-to-battery cable when trying to start your car. If for any reason you are not sure that you can safely do the battery-to-battery cable, it is best to call a professional.
All products produced by Electro Sanat Tehran
- Proudly produced in Iran with warranty and after-sales service
- Warranty period : One year warranty from the date of purchase
- After-sales service : 10 years after the date of purchase
- The material of the body is made of thick iron sheet in order to last as long as possible, and it is painted with color in terms of durability.
all
Tehran’s Electro Sanat devices are made by Iranian engineers and have high manufacturing quality and efficiency .
A word to dear customers
The official site of the collection
Elekctro Sanat Tehran is proudly ready to provide various services in the following fields:
- Providing fully technical and specialized advice regarding the sale of car battery chargers
- Providing fully technical and specialized advice regarding getting a representative from Electro Sanat Tehran
- Selling products in bulk to respected representatives
- Selling products individually to accompanying and dear customers of the collection
- Sending all products to all parts of our beloved country