Getting to know how to turn on the car without a switch and starter

You probably left your key in the car at least once or lost it. As a driver, you should be able to activate the car starter in such cases without the presence of the switch. If you also want to learn practical methods and solve this problem, we have come to help you with this article.

Can the car be started without a switch?

Of course, it will not be easy to start the car without a switch. If you want to do this process in an emergency, you should follow the steps mentioned throughout the article. First of all, we must mention that the process of turning on the car without a switch depends on the type of your car. A factor such as the type of embedded security system will influence the chosen method. For example, imagine a very old arrow; Probably, this car will not have an alarm because it is old. In this situation, you will probably encounter a very old switch brain and you will be able to activate the car starter with another key or even a pointed object. In the following, we will mention all applicable methods.

Car starting methods without the need for a key or switch

  • With the help of a screwdriver or hammer

With the help of these tools, you can activate the car starter in normal models. Of course, doing this method requires precision and expertise because if you are unfamiliar, you may damage the switch input. With the help of this method, you can disable the lock pins. Among its disadvantages, we can mention damage to the key input; so that it may need to be replaced after this method.
In the first step, you need to access the place where the internal locks are located in the ignition. For this purpose, you need to enter about 2 cm into the opening of the switch. You can use a screwdriver or hammer for this. Once you insert the screwdriver, try to turn the ignition on. If you don’t have a screwdriver, you can use a sharp piece of metal.

  • Starting the car with the help of a hot engine

If your car is one of the normal models, this method will also help. For this purpose, remove the plastic cover of the steering wheel. With this, you can access the car’s ignition section. Of course, our advice is to evaluate the car’s wiring before proceeding to make sure that there will be no malfunction. Because in case of wrong wiring, you may burn the expensive electrical equipment of your car.

Be sure to use protective gloves. Be careful that most of the time car battery wires are produced in red color. Brown or yellow wires are related to the car ignition. Cut the end of the cover of the battery wires with the help of a knife so that you can access the wires. When you connect the battery wire to the power wire, the engine will start.

  • Starting the car with the help of red coil wire

In addition to the car battery wires, you can also use the coil wire to start the car. This method is more effective in older model cars. We recommend that you check your car’s wiring diagram before proceeding. Because probably different models have different wiring.

For this, it is necessary to raise the hood of the car. Then go to the underside of the hood. Now you need to look for the red coil wire. With a positive jumper cable, you must establish a connection between the positive terminal of the battery and the wire of the coil. In this method, in fact, you transfer the 12-volt equation directly to the coil.

In order to find the starter wire, you need to look inside the steering wheel. When you can supply electricity to the car in this way, the engine will start.

The best way to start the car if there is no switch

Since the most useful solution for turning on and establishing the car’s electricity without the presence of a switch is to take help from the car’s wiring, we will explain this solution in detail below.

First step, remove the plastic cover around the steering column: Sometimes you have to remove the plastic cover to access the wiring. You will probably see small screws around the steering wheel. You can open them with the help of a suitable screwdriver. After removing the cover, you will be able to see the connector on the back of the switch. The ignition switch is installed on this part. It is necessary to remove the connector for more access to the wires and to shorten them. Of course, you can also do this by cutting the wires.

The second step, identifying the wires: This step is considered the most important step. In some cars, you can see the wiring diagram on the ignition cable. You will hit at least four wires. In order to be able to activate the car starter, you must know what role each wire plays. These wires include gas pump wire + starter motor + equipment + battery.

Wire 1: The color of this wire is white and in terms of size, it may be a little thicker than other wires. Its role is to supply the car with electricity directly from the battery. When you connect this wire to the car body, you will see a spark. Use this method to identify it. But when you connect the other wires to the body, you will not see a spark. Now that you can correctly identify the first wire, it is better to name it. It is generally known as BAT or C. You can use it to identify other wires.

  • In the second step, it is necessary to connect the other three wires to the first wire one after the other momentarily.
  • After connecting, in-car equipment such as recording may be activated. In this case, name it as ACC or PR.
  • If after connecting, you notice that the gas pump starts working or the lights on the display screen (amp) are lit, name it IGN or 15. So that after connecting to the BAT wire, the power reaches the car starter and the car starts. is to quickly separate two wires from each other. This wire is called ST or 50.

The reason for identifying all the wires is to be able to connect the three primary wires, namely ACC, IGN and BAT. Cover these three wires with the help of electrical tape so that they do not have the slightest contact with the ST wire. Finally, it is necessary to make a short circuit with the ST wire to finally activate the car.

Tips:

Connect the ST wire to the other three wires for just a moment and then release it. When you need to turn off the car, disconnect the fuel pump and battery wires. By doing this, the car will turn off immediately.

You may see more wires when looking for the wires behind the switch to start the car. We recommend that you find the same four main wires and don’t do anything with other miscellaneous wires. For example, other branches may have been taken from the IGN wire for other electrical equipment, which will not be of practical use to you.

If the car has a steering wheel lock, you may need to break it in the last process. This will not be easy and you need to apply pressure and use your muscles to do it.

Car starter in cars with immobilizer without the presence of a switch

When your car is a modern model, it will not be possible to start the car without a switch with the solutions mentioned above. In these cars, the main switch must be placed near the car starter to start the car. If this system is not activated with the help of the transponder, the car cannot be turned on.

In other words, starting these cars will be more challenging than old cars and the above methods will not be enough. You cannot activate such cars unless you are able to read their digital codes.

This system is activated when an inductive connection occurs between the switch and the system. If this connection is not established for any reason, the car will not start at all. Of course, in some advanced cars, after every start and stop, the immobilizer provides a new code. It is interesting to know that the same mechanism is also established in the central lock. In fact, the central lock is also controlled by the immobilizer system.

With these interpretations, it can be said that it is not possible to connect the car’s electricity without the presence of the main switch in advanced models. Since these cars follow the online system, even a skilled digital engineer cannot help you. But if your car does not have such a mechanism, you can use the other mentioned methods.

How to turn on the car without starter

Every driver should be able to start the car in critical situations without starting it. Sometimes this happens due to battery failure or faulty wiring. In any case, the following solutions can help you solve this problem.

  • Starting the car without a starter with the help of a rope
  • In the first step, you must pull the handbrake to the end.
  • Place stones or bricks on the sides of the rear tires so that the car does not move.
  • Set the gear to three.
  • Place the switch in its place and turn it to the on position.
  • To install the rope, you must separate the tire on the student’s side from the ground and distance it. Get help from Jack to do this.
  • To use this solution, you must have tools such as towing wire, rope or strong cloth available. Because it is necessary to rotate them at least three turns clockwise around the tire. Pull the wire towards you to make sure it is secure.
  • By doing this process, the car will turn on. Get in the car and put your left foot on the clutch. Then put the gear in neutral position. Now you can pick up the jack and stones and start moving.
  • Starting the car, without starting, with the help of shaking
  • The first situation (when the car is on a slope): in this situation, you need less force to push, so open the switch and pull the handbrake all the way down. Put your foot on the brake pedal and then brake. Release the hand. In the next step, press the clutch to the end. Now you can release the clutch and the brake. If you feel the car starts moving at a high speed, release the clutch more slowly. As the car accelerates, the car will probably start.
  • The second situation (using people as an auxiliary force): In this situation, it is necessary for the driver to pull the handbrake completely down and open the switch. Put your foot completely on the brake and apply the handbrake at the same time. Push down Put your other foot on the clutch and set it to 2. When the people behind the car start to squeal, take your foot off the brake Lift yourself off the clutch slowly to start the car.
اشتراک گذاری